7.10. `Services`
command
7.10.1. Introduction
The `Services`
command enables:
For the Malcore service: force restart or reinstallation
For Sandbox services:
enable or disable the Internet connection network interface
possibility of configuring this interface (IP address, etc.)
configure a proxy
7.10.2. Prerequisites
User : setup
7.10.3. Preliminary operations
Depending on the situation:
either use the SSH access to the configuration menu
either use the Direct connection to the configuration menu with a keyboard and monitor
either use the HTTP access to the configuration menu via iDRAC (DELL server)
either use the SSH access to the configuration menu via the iDRAC interface in serial port redirection mode
7.10.5. Malcore engine service access procedure
The following `Services`
window is displayed.
Select the line
`Malcore service`
or press the letter M.- Click on the
`OK`
button..The`Malcore Services Manager`
window is displayed:Choose a service ----------------------------------------------------------------------------------------- Restart Malcore forcefully Try to restart Malcore if stuck Reinstall Malcore service Wipe out Malcore service and reinstall it
Each of these commands is detailed in the table below:
Command |
Function |
---|---|
|
Forces a restart of the Malcore service: use in the event of a blockage |
|
Reinstall the Malcore service |
To force a restart of the service:
- Select the
`Restart Malcore forcefully`
command and confirm.The`Restart Malcore forcefully`
window is displayed. Wait for the message
`Malcore successfully restarted`
to appear.Click on the
`OK`
button.
To reinstall the service:
- Select the
`Reinstall Malcore service`
command and confirm.The`About to reinstall malcore`
window is displayed.You are about to reinstall. Are you sure you want to continue?
- Click on the
`OK`
button..The`About to reinstall malcore`
window is displayed. Wait for the message
`Malcore successfully restarted`
to appear.Click on the
`OK`
button.
Press the
`OK`
key to return to the main menu.
7.10.6. Procedure for accessing the Sandbox services of the Gnest engine
The following `Services`
window is displayed.
Choose a service
---------------------
Malcore service
Sandbox services
Select the
`Sandbox services`
line or press the letter S.- Click on the
`OK`
button.The`Sandbox Services Manager`
window is displayed:Choose a service ------------------------------ Enable internet ouput Disable internet ouput
Note
Activation of the Internet connection is used by Gnest virtual machines.However, this activation must also be made when configuring the analysis templates: the implementation is described in Procedure to configure the Gnest engine.
Each of these commands is detailed in the table below:
Command |
Function |
See procedure |
---|---|---|
|
Enable Internet connection |
|
|
Disable Internet connection |
7.10.6.1. Procedure for enabling the Internet connection
Select the
`Enable internet output`
command and confirm. | The`Enable internet output`
menu is displayed.Internet output interface Proxy configuration Apply internet configuration
Each of these commands is detailed in the table below:
Command
Function
See procedure
`Internet output interface`
Selection of the physical interface of the GBox physically connected to the Internet (gbx1 to 3)
`Proxy configuration`
Configure an Internet access proxy
Procedure for accessing the Sandbox services of the Gnest engine
`Apply internet configuration`
Apply the Internet configuration
Procedure for accessing the Sandbox services of the Gnest engine
To specify an interface for output to the Internet
Select the
`Internet output interface`
command and confirm. | The`Choose an interface`
window is displayed.Select an interface (e.g. gbx1) and press the
`OK`
key. | The following message is displayed:`you either have to configure gbx1 or choose another interface`
.Press the
`OK`
key to configure the selected interface (here gbx1). | The following message is displayed:`Internet ouput successfully configured`
.Press the
`OK`
key to return to the previous menu.Press the
`Return`
key to return to the previous menu.
To configure a proxy:
Select the
`Proxy configuration`
command and confirm. | The`Proxy configuration`
window is displayed.Enter the IP address.
Enter the port.
Press the
`OK`
key to confirm the entry.Press the
`OK`
key to return to the previous menu.Press the
`Return`
key to return to the previous menu.
To apply changes to the network configuration:
- Select the
`Apply internet configuration`
command and confirm.A number of messages appear and then the`Enable internet output`
menu is displayed. Press the
`OK`
key to return to the previous menu.Press the
`Return`
key to return to the previous menu.
7.10.6.2. Procedure for disabling the Internet connection
- Select the
`Disable internet output`
command and confirm.The`Disable internet output`
window is displayed.You are about to disable internet Please confirm?
Click on the
`Yes`
button to deactivate the internet connection interface.Wait for the message
`Ìnternet ouput successfully disabled`
to appear.Press the
`OK`
key to return to the previous menu.Press the
`Return`
key to return to the previous menu.Press the
`Return`
key to return to the previous menu.